Showing results: 1831 - 1845 of 2684 items found.
-
785809-01 -
NI
8 AI (16-Bit, 3.5 MS/s/ch), 2 AO, 24 DIO, Multifunction I/O Device - The PCIe‑6376 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6376 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included DAQExpress™ companion software provides basic measurement and analysis, while the NI‑DAQmx driver provides the ability to create customized automated measurement and control applications.
-
785813-01 -
NI
PCIe, 8 AI (16-Bit, 500 kS/s), 2 AO, 24 DIO, Multifunction I/O Device - The PCIe-6346 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality, leveraging the high-throughput PCI Express (PCIe) bus and multicore-optimized driver and application software. Because of its multi-ADC architecture, the device offers simultaneous sampling. Onboard NI-STC3 timing and synchronization technology deliver advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe-6346 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
CDN61000-5C -
Lisun Electronics Inc.
• Application Range: ≤4kV, 1.2/50us pulse, 8 wire unshielded twisted pair (UTP) • Test Voltage: Max 4KV, 2 kV (1.2/50 µs pulse when RJ45 connector is connected. Maximum test voltage is 1.5kV when RJ45 female is unconnected or auxiliary terminal is not protected.) • Coupling mode: 90V gas- discharge tube+250ohm Resistor/Each Wire, 8 Wires Simultaneously-Ground (Common Mode) • Input and output interface: RJ45 connector • Terminal layout (RJ45 connector): First pair of lines: pins 1/2 Second pair of lines: pins3/6 Third pair of lines: pins 4/5 Fourth pair of lines: pins 7/8 • Max. operating speed: 1000MBit/s • Max operating voltage: Max 50V DC • Max operating current: Max 1A Related Instruments
-
EK-P4 -
Sensirion AG
The evaluation kit EK-P4 is designed for an easy and cost-efficient evaluation and qualification of Sensirion's SDP3x differential pressure sensors. Test now the features of the new differential pressure sensor. Especially at lowest pressure differences, the sensor provides highest accuracy and long-term stability. The evaluation kit EK-P4 is designed for an easy and cost-efficient evaluation and qualification of Sensirion's SDP3x differential pressure sensors. Test now the features of the new differential pressure sensor. Especially at lowest pressure differences, the sensor provides highest accuracy and long-term stability. The evaluation kit consists of a USB stick connected to a PCB on which an SDP3x differential pressure sensor is already attached. The included flow element can be easily affixed to the kit with two screws and then directly connected to the gas flow. Detailed information about the flow element can be found in the application note.
-
40-196-101 -
Pickering Interfaces Ltd.
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
40-196-001 -
Pickering Interfaces Ltd.
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
T&R Test Equipment Ltd.
Our primary current injection test sets cover from 750A through to 6000A. Available in single phase, testing applications include testing and timing of under and over current relays, circuit breakers and CT ratio testing.
-
Keysight Technologies
The Lightwave Component Analyzer is the instrument of choice to test all relevant opto-electronic S-parameters, like S21, S11 and S22 for electro-optical components in 10Gb/s and 40Gb/s, Fibre Channel and CATV transmission systems as well as radio-over-fiber and A&D applications.
-
JW3224. JW3124 -
Shanghai Joinwit optoelectronic Tech,co.,Ltd
JW3224MPO Optical Power Meter and JW3124MPO Optical Light Source is special for testing MPO fiber. At recent years, as the rapid development of data centre and cloud computing, also with rapid growth of multi fibers” (MPO) requirement. However, on the site of measurement process, traditional single channel Optical power meter with complex measurement and low credibility. Based on this, JW3224&JW3124 MPO products arises at this monment. The product can test the insertion loss of MPO fibers and polarity with only one key, And the integration of a variety of data storage, threshold analysis, data export and other applications，Compared with the traditional instrument, the test efficiency of JW3224 & JW3124 is more than 10 times，it is the best choice for field application of MPO room test、calibration of production line、Determination of polarity.
-
NI
PXI RF Analog Signal Generators deliver the functionality of RF signal generators to the modular, compact PXI form factor. These modules support frequency ranges from 250 kHz to 20 GHz. You can combine PXI RF Analog Signal Generators with other PXI modular instrumentation to design automated test systems for radar, RF integrated circuits (RFICs), and automotive test applications.
-
Russells Technical Products
Our battery test chambers are equipped with safety features conforming to industry safety standards enabling testing to a variety of conditions and specifications including extreme temperature cycling, humidity, vibration, and/or altitude. Russells Technical Products battery test chambers are used in a wide range of battery testing applications including lithium ion, battery packs, lead acid batteries, modules and more.
-
Cincinnati Test Systems
Cincinnati Test Systems (CTS) provides our customers with turnkey systems that include the design, manufacture and support of custom built lean cell and automated functional equipment testing solutions. We are a recognized global leader for providing test solutions integrated with advanced technology, precision instrumentation, information software written by CTS engineers with proven experience, and supported by a team of technical application specialist.
-
W-IE-NE-R, Plein & Baus GmbH
The WIENER 6021 crate series can be outfitted with cPCI, PXI or PXIe backplanes to provide high performance chassis with highly reliable low-noise power supplies for these bus standards. Typical applications are data acquisition, beam line control and test instrumentation.
-
Thermotron Industries
Benchtop Test Chambers provide superior performance over a wide range of applications. Ideal for testing smaller products such as computer components, these chambers combine superior performance with compact design that is perfect for research and development or personal point-of-use testing.
-
Analog Devices Inc.
Analog Devices offers ultralow jitter clock generation products for wireless infrastructure, instrumentation, broadband, automatic test equipment, and other applications demanding subpicosecond performance. Our clock products are ideal for generating the high speed, low noise clock signals required to clock high performance analog-to-digital converters (ADCs) and digital-to-analog converters (DACs). ADI clock ICs integrate PLL cores, dividers, phase offset, skew adjust, and clock drivers in small chip scale packages.
